X8000(M57)怎么开启AMT呢?

djhanfei

装了驱动后老是提示AMT已经禁用,需要联系管理员开启,但是要怎么开启了?

lichunhua

开机的时候有提示，按ctrl+P就可以进入，不过更具体的设置要查阅说明书，默认的进入密码是admin

zgwwhy

这个问题我老早就碰到了3台x8000全都这样 ctrl+p进去也无法解决哪位高人能搞定这个问题那真是功德无量！

lichunhua

http://www.intel.com/cd/network/ ... apac/zho/217823.htm
http://software.intel.com/zh-cn/ ... /?cid=sw:prccsdn561
后一个地址里的内容可以解释你在你自己的机器上是需要特定设备才能够达成启用ＡＭＴ的目的　

工厂模式： Intel AMT 3.0以前的版本的机器，用户买回来以后，接上电源和网线，这个时候Intel AMT没有IP地址，也不开放任何监听端口，管理服务器是无法连接和扫描到此机器的Intel AMT的，这就是我们所说的工厂模式。当用户通过进入MEBX手动或通过USB盘自动设置好机器的PID和PPS后，Intel AMT从工厂模式变成设置模式。3.0及以后的机器由于引入了零接触配置，用户买回的新机器即使不做任何配置也能自动发送“Hello”包到配置服务器，因此此时处于设置模式，而不是工厂模式；但是在接上电源后的一段时间内（一般是24小时），如果没有配置服务器能自动配置好此机器的Intel AMT，则Intel AMT自动关闭自己的网络接口，可以认为这个时候此机器也是进入了工厂模式；只有当位于操作系统之上的软件发送一个激活命令之后，才能重新将Intel AMT从工厂模式变为设置模式。
设置模式：处于设置模式的Intel AMT就可以主动按一定的规律朝配置服务器发送“Hello”消息了；配置服务器接收到此“Hello”消息后，会主动将对应的机器的Intel AMT按配置服务器实现配置的设置配置好；在配置成功以后，Intel AMT就从设置模式进入到可操作模式。
可操作模式：处于此状态下的Intel AMT才算是可以真正开始发挥其强大功能，这时，我们可以通过WebUI、SOAP接口和WS-MAN（3.0及以后版本）接口来远程主动管理。通过远程调用接口提供的Unprovision命令，或者是通过MEBX菜单中的Unprovision选项，Intel AMT又可以从可操作模式变回设置模式或工厂模式；一般来说Partial Unprovision是将Intel AMT从可操作模式变为设置模式，Full Unprovision是将Intel AMT从可操作模式变为工厂模式。

djhanfei

专业啊

zgwwhy

M57 (Non-AMT) shows the CTRL+P prompt, AMT Sub-Menu and AMT Driver - ThinkCentre M57 (type 6062, 6065, 6071, 6076, 6089, 9182, 6019, 6066, 6072, 6077, 6087, 9181, 6008, 6068, 6074, 6079, 6082, 9172, 6010, 6069, 6075, 6081, 6086, 9174)

Applicable countries and regions

Symptom

M57 (Non-AMT), you may have three possible questions for the following:

BIOS 2RKT28A or earlier BIOS versions, you will find an AMT Sub-Menu in the BIOS Setup "Advanced" page.
When the M57 boots up, after the "ThinkCentre" logo, you will see a "CTRL+P" Option. If the you select"CTRL+P", the MEBx interface will be shown.
M57 is a Non-AMT model, but the AMT drivers are still needed to prevent a yellow bang from showing in Device Manager. With some M57 preloads or after the installation of AMT driver, there may be a pop-up window when booting into Windows Vista/XP to show the AMT status.

Affected configurationsAny of the following systems running Microsoft Windows XP Professional, Windows XP Home, Windows Vista:

ThinkCentre M57(type 6062, 6065, 6071, 6076, 6089, 9182, 6019, 6066, 6072, 6077, 6087, 9181, 6008, 6068, 6074, 6079, 6082, 9172, 6010, 6069, 6075, 6081, 6086, 9174)

SolutionSymptom 1 above:
BIOS versions after 2RKT28A have corrected this issue. The BIOS will hide the "AMT Sub-Menu" for Non-AMT systems.
Download the current BIOS version HERE
LimitationSymptom #2 above is a limitation.
M57 systems will show the "CTRL+P" prompt, enter the MEBx with the default password 'admin'. After changing the default password, you will be able to view and change some settings, but the MEBx interface for the M57 is different from the M57p (AMT model).
MEBx Main Menu:

M57, AMT is disabled, so the M57 has no "AMT Configuration" item. You cannot configure any AMT settings.
MEBx -> ME Platform Configuration

On M57, there is no "ME feature Control" item, so you cannot enable AMT.
You can update the ME FW on your M57, but just to update the ME code. The configuration (e.g. AMT enable/disable) cannot be updated or refreshed by updating the FW. You can also change the ME Power Control. The default on M57 is "Desktop: On in S0", which means the ME will be active only in S0 power state. Changing this setting will increase power consumption, but have no other effect on the system's function.
Symptom #3 above is a limitation.
M57 systems have no AMT features, but still need the ME for Intel® QuietSystem Technology (Intel&reg QST). The thermal solution Intel® QST is controlled by the ME. The ME has an interface to the operating system, named HECI (Host Embedded Controller Interface). This interface needs a driver (HECI driver). On an M57, the AMT features in ME are disabled, but the AMT host interface still exists.
This interface needs the Local Management Service (LMS), Serial Over Lan (SOL) LMS_SOL drivers. Otherwise, there will be a yellow bang in Device Manager.
The pop-up window can be disabled by running "C:\Program Files\Intel\AMT\disable.reg". This will stop the application, when Windows boots, to disable the pop-up window.
A new driver, without the pop-up window, has been built and released to the preload for M57 and M57p. This new driver, without the pop-up window, will be released on our website for both M57 and M57p.

The above information will be updated once the new driver has been released to the Lenovo support web site.