有用ET128-2在linux使用的吗？

jifeng3518

有用ET128-2在linux使用的吗？我用usb_modeswitch但是不行

usb_modeswitch.conf的配置文件
   1. # vi usb_modeswitch.conf
   2. ########################################################
   3. # Huawei E180/158/128-2
   4. #
   5. # Contributor: Tom Dawahare
   6.

   7. DefaultVendor=  0x12d1
   8. DefaultProduct= 0x1da1  
   9.

  10. ;TargetClass=    0xff
  11.

  12. # choose one of these:
  13. DetachStorageOnly=0
  14. HuaweiMode=1

然后使用usb_modeswitch -W，执行后好像程序假死，一直处于等待，执行后的信息如下：

   2. Reading config file: /etc/usb_modeswitch.conf
   3.

   4. * usb_modeswitch: handle USB devices with multiple modes
   5. * Version 1.0.5 (C) Josua Dietze 2009
   6. * Based on libusb 0.1.12

   8. DefaultVendor=  0x12d1
   9. DefaultProduct= 0x1da1
  10. TargetVendor=   not set
  11. TargetProduct=  not set
  12. TargetClass=    not set

  14. DetachStorageOnly=0
  15. HuaweiMode=1
  16. SierraMode=0
  17. SonyMode=0
  18. MessageEndpoint= not set
  19. MessageContent= not set
  20. NeedResponse=0
  21. ResponseEndpoint= not set
  22. Interface=0x00


  24. InquireDevice enabled (default)
  25. Success check disabled

  28. Looking for default devices ...
  29. Found default devices (1)
  30. Accessing device 003 on bus 001 ...
  31. Using endpoints 0x05 (out) and 0x85 (in)
  32. Inquiring device details; driver will be detached ...
  33. Looking for active driver ...
  34. OK, driver found ("dummy")
  35. OK, driver "dummy" detached
  36. 程序一直就在这里阻塞了,一直处于等待状态
  37. 不晓得是什么问题

tlshwp

能用，我用过的！

tlshwp

我是在XP下装的虚拟机，启动LINUX后用USB_MODESWITCH是可以用的！

tlshwp

用USB_MODESWITCH驱动后用DMESG查看，会多出3个ACM设备分别是：acm0、acm1、acm2

cristo

没用过那设备,我用的LC5730+wvdial

tlshwp

下个wvdial 安装上用它拨号就OK！

hehetaoka

不需要使用usb_modeswitch，最新固件自带驱动可以用啊~

hehetaoka

同6楼的兄弟~

子曰诗云

我是
我能sudo wvdial

子曰诗云

sudo usb_modeswitch -W

* usb_modeswitch: tool for controlling "flip flop" mode USB devices
* Version 1.0.2 (C) Josua Dietze 2009
* Works with libusb 0.1.12 and probably other versions

Reading config file: /etc/usb_modeswitch.conf
DefaultVendor=  0x12d1
DefaultProduct= 0x1da1
TargetVendor=   0x12d1
TargetProduct=  0x1da1
TargetClass=    not set

DetachStorageOnly=0
HuaweiMode=1
SierraMode=0
SonyMode=0
MessageEndpoint= not set
MessageContent= not set
NeedResponse=0
ResponseEndpoint= not set
Interface=0x00

InquireDevice enabled (default)
Success check disabled

usb_set_debug: Setting debugging level to 15 (on)
usb_os_find_busses: Found 003
usb_os_find_busses: Found 002
usb_os_find_busses: Found 001
usb_os_find_devices: Found 002 on 003
usb_os_find_devices: Found 001 on 003
error obtaining child information: Inappropriate ioctl for device
usb_os_find_devices: Found 002 on 002
skipped 1 class/vendor specific interface descriptors
usb_os_find_devices: Found 001 on 002
error obtaining child information: Inappropriate ioctl for device
usb_os_find_devices: Found 004 on 001
usb_os_find_devices: Found 001 on 001
error obtaining child information: Inappropriate ioctl for device

Looking for target devices ...
Found devices in target mode or class (1)
Looking for default devices ...
Found default devices (1)
Accessing device 002 on bus 003 ...
Using endpoints 0x05 (out) and 0x85 (in)
Not a storage device, skipping SCSI inquiry

Device description data (identification)
-------------------------
Manufacturer: HUAWEI Mobile
     Product: HUAWEI Mobile System Solution
  Serial No.: 000000-00-0000000
-------------------------
Sending Huawei control message ...
OK, Huawei control message sent
-> Run lsusb to note any changes. Bye.

aaa@Think:~$ sudo gedit /etc/usb_modeswitch.conf
aaa@Think:~$ sudo wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Sending: AT+CGDCONT=1,"IP","cmwap"
AT+CGDCONT=1,"IP","cmwap"
OK
--> Modem initialized.
--> Sending: ATDT*99***1#
--> Waiting for carrier.
ATDT*99***1#
+CGREG: 2
CONNECT 2800000
--> Carrier detected.  Starting PPP immediately.
--> Starting pppd at Wed Apr 21 19:38:50 2010
--> Pid of pppd: 4034
--> Using interface ppp0
--> pppd:

jifeng3518

硬件是ET128-2  不是ET128哦

szsaihe

如何在linux下锁定TD，这个才是技术活呀